2024 Land Pride RC2512 Series

GEARBOX WARRANTY
5 Year Limited Gearbox Warranty demonstrates our confidence in the gearbox's quality and lasting performance.

1-1/2" CUTTING CAPACITY
These cutters offers 1-1/2" cutting capacity. See Operator's Manual for more information.

OPTIONAL LP PERFORMANCE HITCH
Clevis swivels two ways: Cutter can swivel clockwise and counterclockwise about tractor drawbar up to 12° in either direction.

ADJUSTABLE JACK ANGLE
Helps keep park jack vertical when in use.

LED SIGNAL LIGHTS
LED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.

BEVELED SKID SHOES
Wing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.

10 GAUGE STUMP JUMPER
Round stump jumper allows cutter to slide over obstructions protecting gearbox output shaft & bottom seal.

SPRING CUSHION
Deck-mounted spring cushion provides a smooth ride in rough terrain.

DUAL LEVELING RODS
Dual leveling rods enable the cutter to pull equally on the rear axle during travel over rough terrain.
NARROW TONGUE DESIGN
Narrow tongue design handles tight turns - great size for country estates.
Specifications & Capacities Tractor horsepower 40-100 hp (30-75 kW) Gearbox horsepower Splitter Center & wings 160 hp (119 kW) 100 hp (75 kW) Gearbox shafts Input shaft Output shaft 1 3/8" (3.5 cm) 6 Spline 1 1/2" (3.8 cm) Gearbox capacity & lubrication Splitter Center & wings 4.5 pints (2.13 L) of gear lube 80-90W EP 4 pints (1.89 L) of gear lube 80-90W EP Cutting capacity 1 1/2" (3.8 cm) Hitch weight 793 lbs (359.7 kg) Machine weight 2,540 lbs (1152.1 kg) Blade tip speed At 540 rpm Center Blades = 16,500 FPM (83.8 mps) Wing Blades = 16,000 FPM (81.3 mps) Hitch types LP Performance hitch and swivel hitch Hitch jack Standard (2,000 lbs) (907.2 kg) Cutting width Overall cutter width Minimum transport width 12'-0" (3.66 m) 12'-7" (3.84 m) 7'-11" (2.41 m) With front cutting blade 1 1/2" (3.8 cm) off the ground. Overall length 13'-3" (4.04 m) Deck height 11" (27.9 cm) Cutting height 1 1/2" to 12" (3.8 cm to 30.5 cm) Lift hydraulics 2 1/2" bore x 8" stroke hydraulic cylinder, hoses, fittings and stroke control spacers Wing folding hydraulics 2" bore x 8" stroke hydraulic cylinders, hoses, and fittings Wing flex while operating Max. 20o down, can float up as needed as long as the wheel(s) are still on the ground. Wing transport protection Wing transport locks Deck material 10 Gauge (3.4 mm) deck Side skirt material 3/16" (5 mm) Plate Skid shoes Wing deck: 1 replaceable per wing Center deck: 2 replaceable shoes Blade rotation Left wing Center deck Right wing Counterclockwise Counterclockwise Clockwise Blades - 6 (2 per deck) 1/2" x 3" (1.3 cm x 7.6 cm) Heat treated free swinging alloy Steel with up lift Blade overlap 6" (15.2 cm) Blade bolt Keyed with hardened flat washer and locknut Stump jumper / blade holder 10 Gauge (3.4 mm) round dish shaped pan, reinforced with 1" x 3 1/2" (2.5 cm x 8.9 cm) blade bar Front & rear guards Single chain Input driveline Category 4 with constant velocity u-joint Intermediate & wing drivelines Category 3 with slip-clutch Wheels 20.5" x 6.75" x 10" (52.1 cm x 17.1 cm x 25.4 cm) used aircraft tires or 21" (53.3 cm) laminated wheels Number of wheels 4 - Wheels: 2 on transport axle and one on each wing axle Transport axle Spring-cushioned lift cylinder Signal lights 7 Pin connector LED SAE J560 pin configuration Hubs Cast iron five-bolt hubs with tapered roller bearings and 1 3/4" (4.4 cm) shafts.